你的位置:首页 > 公司产品 > 常见问题

奇田热水器打不着火怎么办?

更新:2016/5/10 16:27:28      点击:
  • 产品品牌   
  • 产品型号   
  • 产品描述

    ...

产品介绍
奇田热水器打不着火怎么办?
一、电源疑问
热水器打不着火的解决方法:检查交流电源插头指示灯是否亮,先排除电源供电部分的疑问.
二、电磁阀故障
热水器打不着火的解决方法:若焚烧的时候只听到焚烧声,没有电磁阀“嗒”磁吸声,可能为电磁阀损坏或者老化,电磁阀老化,会不受控制,在打火开始时能吸合一下,打得着火,但随即闭合又熄火了;也可能为燃气压力过高或过低,使用钢瓶气的热水器会出现钢瓶减压阀输出压力过高或过低使用热水器不能打着火;更可能为电磁阀有脏物。电磁阀不能过气,燃气(天燃气、液化石油气、人工煤气)就不能出来,不能出来,以致点不着火。在确认电磁阀好坏之前要确认焚烧器控制电路是否正常,若有故障,不能控制电磁阀吸合。
三、电焚烧器故障
热水器打不着火的解决方法:脉冲焚烧器和控制器有一方有故障,热水器均不能焚烧。
四:焚烧瓷针或感应瓷针疑问
热水器打不着火的解决方法:a.焚烧针偏位或老化时焚烧十分困难,可替换或将焚烧针正确安放;b.感应老化,可将感应擦亮安放好(使火焰不管大火还是小火能充分烧着感应针)即可。
五、水压疑问
热水器打不着火的解决方法:a.水压低时热水器无法正常启动;
b.进水处过滤网堵塞造成水无法正常流过,整理干净就可以。
六、水气联动装置故障
热水器打不着火的解决方法:a.水气联动阀内鼓膜老化或损坏不能推动微动开关;
b.微动开关坏。
七、气源开关未打开或进气滤网堵塞
热水器打不着火的解决方法:开启气源,整理进气过滤网。
八、气种不符
热水器打不着火的解决方法:比如将液化气热水器接到天然气上等,p这种情况需要将液化气热水器改天然气后才可以接入使用。
九、气门密封件被燃气腐蚀后发涨。
热水器打不着火的解决方法:替换零部件。
十、烟管无法正常排气
热水器打不着火的解决方法:a.烟管有堵塞,整理烟管堵塞物;b.烟管过长,未正确安装。
Strange field water heater won't catch fire?
A, question for power supply
Water heater can't fire solution: check the ac power plug lights are bright, to rule out power supply part of the question.
Second, the electromagnetic valve failure
Water heater can't fire the solution: if only heard burning burning, no \"click\" magnetic absorption electromagnetic valve, may be electromagnetic valve damage or aging, aging of the solenoid valve, will not be controlled, can suck at the beginning of the lighter one, played on fire, but imtely closed stalled again; May also for the gas pressure is too high or too low, using cylinder gas water heater will appear the cylinder pressure reducing valve output pressure too high or too low to use water heater can't play on fire; Is more likely for the solenoid valve with dirt. Electromagnetic valve cannot pass gas, gas, natural gas, liquefied petroleum gas, artificial coal gas) will not be able to come out, can't come out, so that doesn't work. Before confirm the solenoid valve is good or bad to confirm incinerator control circuit is normal, if there is failure, unable to control the electromagnetic valve and off.
Three, the electric fault incinerator
Water heater can't fire solution: pulse burning and controller one party has fault, water heater is not burning.
Four: burning or induction porcelain porcelain needle
Water heater can't fire the solution: a. pin offset or aging burned very difficult, can replace or would fire needle was right; B. induced aging, can be induced to polish stow (regardless of the flames of the fire or a small fire can be fully burning sensing needle).
Five, the water pressure
Water heater can't fire solution: a. water down when the water heater can't normal boot;
B. filter clogging caused water to flow through water, clean can.
Six, moisture linkage of failure
Water heater can't fire solution: a. moisture linkage cannot push valve inside tympanic membrane aging or damage to the micro switch;
B. micro switch bad.
Seven, air switch is not open or inlet filter clogging
Water heater can't fire solution: open air supply, air intake filter.
更多产品
友情链接:秒速时时彩  秒速时时彩投注  秒速时时彩  秒速时时彩注册  秒速时时彩  秒速时时彩登陆  秒速时时彩是官方的吗  秒速时时彩开奖结果  秒速时时彩是官方的吗  秒速时时彩官网  秒速时时彩规律  秒速时时彩玩法  秒速时时彩  秒速时时彩是官方的吗  秒速时时彩玩法  秒速时时彩  秒速时时彩官网  秒速时时彩登陆  秒速时时彩计划  秒速时时彩注册  
秒速时时彩,秒速时时彩官网,秒速时时彩网站,秒速时时彩平台,秒速时时彩注册,秒速时时彩开户,秒速时时彩登陆,秒速时时彩投注,秒速时时彩玩法,秒速时时彩计划,秒速时时彩网址,十分六合彩是真的吗,秒速时时彩开户,秒速时时彩计划秒速时时彩开户秒速时时彩注册网址,秒速时时彩规律,秒速时时彩是官方的吗,秒速时时彩开是骗人的吗/秒速时时彩哪里有/秒速时时彩论坛,秒速时时彩开奖结果